Logic and flow steps control when an Automation Workflow in Prospect CRM moves on, which path it takes and how often it repeats. You can find them under Logic & Flow in the Add a New Step window. You need to be a CRM Admin, and the workflow must be open in edit mode. To add a step, see Use the workflow builder.
Wait
The Wait step pauses the workflow for a set amount of time before moving to the next step. Set up these fields:
Days: 0 to 365.
Hours: 0 to 23.
For example, wait 3 days before sending a chaser email.

Wait Until
The Wait Until step pauses the workflow until a particular date and time. Choose a Type:
Type | How it works | Example |
Fixed | Waits until a specific date and time you choose. | Wait until 09:00 on 1 December. |
Dynamic | Waits until the next matching Day Of Week (choose one or more days) or Day Of Month (1 to 31), within a time window (Between _ And _ hours). | Wait until the next Monday or Wednesday between 9 and 11. |
Inferred | Waits until a date taken from a field on the triggering record. | Wait until the Opportunity's expected close date. |
đNote: Dynamic times use your system's time zone. Inferred dates are read when the workflow reaches the Wait Until step. If the date on the record changes after that, the wait isn't recalculated.
If
The If step splits the workflow into different paths depending on conditions.
â ď¸Important: If you add an If in the middle of a workflow, every step that came after it is moved onto the first path (Path 1) automatically. The Else path starts empty. Until you add conditions to Path 1, every record goes down that path, so the workflow behaves as it did before. Add your conditions, then connect or add steps on the other paths.
To set up an If step, follow these steps:
Click Configure Logic.
Set up each path using the path settings below.
Click Add new path to add more paths.
Records that don't match any path go down the Else path. The Else path shows 'The flow doesn't match any of the above paths'.
â

Path settings
Path name: Paths are named Path 1, Path 2 and so on. You can rename them to describe what they're for, for example 'High value'.
When: The conditions for the path. Click Add condition or Add Filter to build them using fields on the triggering record or outputs from earlier steps. All conditions on a path must be true.
Then go to: The step the workflow goes to next when the path matches. You can also connect it on the canvas.

How paths are evaluated
Order: Paths are checked from top to bottom, and the first path that matches is used. Click Move Up or Move Down to change the order.
Paths with no conditions: A path with no conditions matches every record that reaches it, and you'll see a warning. Use the Else path for 'everything else' instead.
Unconnected paths: If the chosen path (or Else) isn't connected to a step, the run ends there.
Deleting a path: This also removes all the steps after it on that path. You'll be asked to confirm first.
Joining paths back together: Paths don't have to stay separate. Connect the end of each path to the same step and they all continue from there. For example, after a high-value path creates a call task and the Else path sends an email, both can join up again at a shared 'Wait 7 days' step.
Loop
The Loop step sends the workflow back to an earlier step so that part of the workflow repeats. Choose the step to go back to. You can only connect a Loop to a step that comes before it.
Loop limit: How many times the loop can repeat, from 1 to 5. The default is 3. The line on the canvas shows 'Up to 3Ă'.
Done: Once the limit is reached, the workflow continues down the Done path instead.
For example: Send chaser email, then Wait 3 days, then If the Quote is still open, go back to 'Send chaser email' (up to 3 times). When the loop is Done, create a task for the account manager.
Set Variables
The Set Variables step creates named values that you can reuse in later steps of the workflow.
Click Add New Variable, then enter a name using letters and numbers only.
Enter a value. You can type a fixed value or use merge fields.
Variables then appear as merge fields in every later step, so you can insert them wherever you need that value.
Why use variables
If the same value is used in several steps, set it once in a Set Variables step and insert the variable everywhere you need it. If the value ever changes, you only need to update it in the Set Variables step. You don't have to find and edit the typed-in value in every step that uses it.
For example, if several emails and tasks in a workflow mention your support email address, store it in a variable called SupportEmail. When the address changes, update the variable, and every step that uses it picks up the new address.
Select Value
The Select Value step picks one value from a list, which is ideal for sharing work fairly across a team.
Under Select from, choose one of these options:
Users: Any active user.
Account Managers: Active users who are set up as account managers.
Specific Users: A list of users you choose.
Manual Values: A list of values you type in.
Under Using, choose one of these options:
Round Robin: Takes turns through the list in order, one per run.
Random Selection: Picks at random.
The result is available to later steps as Selected Value. For example, use Select Value (Specific Users, Round Robin), then a Create Task step assigned to the Selected Value, to share new Enquiries evenly across your sales team.
